By Greg Allan, tradesman and creator of Data First Coaching
Should a tiler hire a qualified tradesperson or an apprentice first?
A tiler's first hire needs to be a qualified tradesperson, not an apprentice. The first hire has to take enough off the owner's plate straight away: laying tile, prepping floors, running membrane into a shower recess, without needing to be trained or watched. An apprentice cannot do that yet, and the owner does not have spare hours to teach one while still quoting and running the business.
Why can't a tiler afford to train an apprentice as the first hire?
Most tiling businesses start as one person doing every job: quoting a bathroom by the square metre, negotiating a day rate with a builder on a renovation, ordering tile supply, chasing breakage replacements, and still laying the floor preparation and screed themselves. There is no spare time in that week to stand over an apprentice.
An apprentice needs close supervision on every stage of a wet area job: setting falls correctly, running the membrane past a shower recess, checking levelling clips on large format tile before the grout goes in. That supervision has to come from somewhere. If the owner is the only qualified person on site, the apprentice either slows the owner down or works without the oversight that waterproofing and warranty work actually need.
A tiler who hires an apprentice first often finds the business has not freed up at all. The owner is still the only one who can be trusted on the membrane, so the apprentice becomes another person to manage rather than another pair of hands bringing in square metre and day rate work.
What happens when warranty backed wet area work sits on unsupervised hands?
Waterproofing in a bathroom or kitchen renovation carries a warranty, and a builder expects that warranty to hold long after the job is signed off. A fault in the membrane or the falls under a shower recess can take years to show up, and when it does, it comes back to the business that installed it.
A callback on a wet area, a leak traced to a shower recess, a comeback that eats a week the business did not plan for: these often get put down to bad luck. The data behind most of these comebacks usually shows the same root cause, a warranty backed job that went to someone who was not experienced enough to be trusted on it unsupervised. For a tiler, the first hire decision is not only about output, it is about where the risk sits.
What should a tiler's first hire look like?
Your first hire should already have the skill and the attitude in place, someone who can run floor preparation, apply membrane and set falls, and lay large format tile without you checking every step. That is the hire that breaks the ceiling of you being the only billable pair of hands in the business.
A first hire like this has to free you for the roles only you can do: quoting square metre work, managing the builder relationship, sorting tile supply and breakage, keeping the pipeline of day rate jobs moving. If the first hire still needs training and supervision, the ceiling stays exactly where it was, because you are still the only one who can be trusted on a wet area.
How does a qualified tradesperson change what a tiler can take on?
A qualified tradesperson on the tools full time is often more efficient than even a very good owner, because their whole day stays on cash generating work: tiling, screeding, waterproofing. The owner is always being pulled away into supplier calls, quoting and scheduling with builders.
This is where AI agents can change the picture for a tiler. An AI agent is software that does a job the way you would, with your prices, your wording and your rules. Set correctly, agents can take on the non-billable work that pulls you off the tools, chasing a supplier on tile supply, following up a quote with a builder, keeping a schedule updated, so the time your business pays for goes on the square metre and day rate work that actually bills. A data first view of your own quoting and job numbers shows whether a qualified tradesperson's added output is covering the wage, rather than guessing from a feeling at the end of a busy month.
When does hiring an apprentice become the right move for a tiler?
An apprentice becomes the easier second hire once a qualified tradesperson is already on the crew, because the apprentice learns under that tradesperson's supervision on site, not under the owner alone. That is the point where taking on an apprentice adds capacity instead of adding a training load.
Picture a tiling business that had been running with two qualified tradespeople on the tools, a costly way to staff square metre and day rate work when one of those wages could instead be spread across more jobs. The owner restructured the crew so a qualified tradesperson now works alongside a second year apprentice, instead of a second full wage for another qualified tradesperson. The qualified tradesperson runs the wet area work and keeps an eye on the apprentice, and the business carries one less full rate wage across the same jobs.
A tiler who delays that first qualified hire, staying a sole trader on every job, is capping how much square metre and day rate work the business can take on at once. The sequence matters: skilled hire first, apprentice once there is someone capable for them to learn alongside.
How does Data First Coaching approach this?
Data First Coaching starts from the tiler's own numbers before talking about who to hire next: the split between square metre and day rate jobs, the margin sitting on waterproofing and wet area work, and how much of the owner's week is still going on quoting and builder calls rather than tiling. The Trade Business Intelligence reads that against patterns seen across other tiling businesses, so the advice starts from this business, not a generic checklist.
Greg Allan puts the hiring sequence plainly: “If you're a sole trader, the longer you wait before you hire a tradesperson, you are capping yourself.” The how, working out what the business can actually afford to pay and when, is worked through inside the Academy, with members, because the Trade Business Intelligence is powered by every member who is open minded, innovative and willing to share what they learn.
Looking for a business coach who starts from your numbers? Tiler Business Coach or every answer for tilers.

