By Greg Allan, tradesman and creator of Data First Coaching
Will a CNC machine actually fix the margin problem?
A CNC machine on its own rarely fixes a margin problem, because the machine only changes how fast boards are cut, not whether the workshop's hours are being sold. Most small joinery businesses weigh a CNC up against cutting speed, nesting efficiency and how many sheets it can get through in a day. That is the wrong measure. The number that matters is billable hours against hours paid across the whole workshop team, CNC time included.
If a cabinetmaker's crew is only billable a fraction of the day because of rework, edging that does not line up, or panels cut twice because the shop drawings changed, a faster machine just produces the same waste quicker. The real question is whether non-billable time in the workshop, not the cutting itself, is what is quietly eating into the margin on every kitchen, wardrobe and vanity quote.
What does workshop time really cost a cabinetmaker if nobody tracks it?
Workshop time that is not tracked against the job it belongs to almost always costs more than the owner thinks, because labour, edging, hardware fitting and rework get absorbed into overhead instead of sitting against the job that caused them. A cabinetmaker can have gross profit margin looking fine on paper while the bank account tells a different story once the real hours are counted.
Picture a joinery business doing mostly kitchens and vanities for two or three regular builders. The quotes look solid, the workshop is busy, but the owner cannot say how many of those hours were actually billable last month versus how many went on fixing a panel that was cut wrong, waiting on a site measure that did not match, or reworking laminate edges after an install day went sideways. Without that number, a capital decision like a CNC is a guess dressed up as a plan.
What should you look at before signing finance on a CNC?
Before you sign finance on a CNC, you want to see actual hours on the job against billable hours for the workshop, including current cutting, edging and panel prep, so you know whether the bottleneck is really in the workshop or somewhere else, like site measures, design sign-off or install days. That one number tells you whether a CNC buys back billable capacity or just produces boards faster while the real hold-up sits unchanged.
It also changes what efficiency means for your business. If your workshop currently runs close to fully billable and a CNC lifts that further, the gain compounds, because the extra output sits on top of a margin that is already thin after board, hardware and labour cost. That is a very different outcome from a workshop that is already losing hours to rework, where a CNC just moves the same waste faster through the shop.
The other thing to check before finance is signed is how the machine's running cost, lease or loan repayment and operator hours get booked. If they sit as a direct cost against the kitchens and vanities the CNC actually cuts for, gross profit margin on each job stays honest. If they get folded into general overhead instead, every quote looks healthier than it really is, and that gap only shows up later, usually at tax time or when cash is tight.
How do AI agents change what a CNC decision looks like?
AI agents, which are software built to do a job the way you would, with your prices, wording and rules, can take on the tracking that most cabinetmakers never get around to doing by hand, so the billable-hours-against-hours-paid number exists before the finance paperwork is signed, not after. That turns a CNC decision from a gut feeling about cutting speed into a data first decision about what the workshop is actually doing with its time.
The same agents can keep CNC running cost, edging time and operator hours sitting against the right job as the work moves through the shop, rather than getting lumped into overhead at the end of the month. For a cabinetmaking business juggling kitchens, wardrobes and vanities for several builders at once, with lead times that slip and shop drawings that change, that kind of ongoing tracking is the difference between a CNC that genuinely lifts margin and one that just looks good in the workshop.
Is a CNC ever the wrong call for a small joinery business?
A CNC can be the wrong call when the real bottleneck sits outside the workshop, in site measures that are slow to turn around, design sign-off that drags on, or install days that blow out because hardware or benchtop supply did not arrive on time. In that case, faster cutting does not free up more billable hours, it just means boards sit waiting longer for the next stage.
Some cabinetmakers are better served keeping flat pack or two pack work going as it is and putting the investment into tightening up the handover between site measure, design and workshop instead. Being fair to the machine matters here: a CNC is not wrong for small joinery businesses in general, it is wrong for a specific business whose own numbers show the hours are being lost somewhere else.
How does Data First Coaching approach this?
Data First Coaching, created by Greg Allan, starts from the cabinetmaker's own numbers through the Trade Business Intelligence, not from a brochure on cutting speed. That means looking first at billable hours against hours paid across the workshop, including CNC time, edging and panel prep, to see where the real problem starts before any capital spend is considered. Greg puts it plainly when a workshop lifts from fully billable to even a little above it: “that's double the amount of profit”, because the extra output sits on top of a margin that was already thin. The how, working through that number for a specific joinery business, is worked through inside the Academy, with members, because the Trade Business Intelligence is powered by every member who is open minded, innovative and willing to share.

