By Greg Allan, tradesman and creator of Data First Coaching
Why does cure time keep blowing out the program on a waterproofing job?
A membrane does not read the builder's program. Cure time depends on substrate, thickness, humidity and temperature on the day, and the figure written into the schedule is usually a standard number, not what that particular wet area, balcony or basement actually needs. When the real cure time runs longer, the waterproofer is the one going back for extra inspections, holding the flood test until the membrane is genuinely ready, and fielding calls from the builder asking when the tiler can get in.
This happens across every job type a waterproofer takes on: a bathroom reline, a balcony re-waterproof after a leak, a roof deck on a new build, a basement with a tight access window. The pattern repeats most through the cooler, wetter months of the year, when ambient conditions slow the cure down further and the backlog of re-inspections stacks up across several jobs at once.
Why does the job still look fine on paper when cure time runs long?
On the books, the job looks the same as it always did. The waterproofer still charges the quoted price, the invoice still gets paid, and the bank balance still moves in the right direction. What does not show up is the extra visit to check the membrane, the second flood test, the follow-up call to the builder and the tiler to reset the start date.
Because the money still arrives, the waterproofer rarely stops to ask what those extra visits actually cost against the hours the quote assumed. The delay reads to everyone else as a scheduling problem between the builder and the tiler. For the waterproofer it is a cost that was never priced, never raised as a variation, and never separated from the job's apparent profit. Job after job, that gap is where the real gross profit margin erodes, quietly, while the figures on the invoice stay exactly as quoted.
How do you turn an overrun cure time into a cost you actually capture?
You start by treating the hours actually spent on a job, not the hours quoted, as the number that matters at the point you notice cure time has run past what the program allowed. That is the moment to check gross profit margin on that job, not at the end of the month when the figures are already old and the variation window has closed.
This is where an AI agent earns its keep, because an agent is software that does a job the way you would do it, using your prices, your wording and your rules. Set correctly, an agent can flag the day a cure time runs over the program, record the extra visit against that job, and prompt you to raise a variation with the builder while the membrane is still curing, not three jobs later when the margin has already gone.
This is data first thinking: the decision about whether to raise a variation comes from what the job is actually costing you right now, not from memory of how the last similar job went.
What changes when AI agents track cure time and flood tests for you?
An AI agent can watch the gap between the programmed cure time and the actual date the flood test passes, and log every re-inspection, standby visit and follow-up call against that specific job as it happens, using the rates and wording you already use for variations.
For a waterproofer running several jobs at once, across bathrooms, balconies, roof decks and remedial work for insurance claims, that gap is easy to lose. An agent does not lose it, because it is not relying on memory of a conversation with the builder three weeks ago. It is working from what was actually recorded against the job, which is exactly why AI agents can hold a line that memory and a busy diary cannot.
Should you keep using a scheduling app to manage cure times and certificates?
Some off-the-shelf scheduling or job management tools genuinely suit some waterproofing businesses, and your own data will show which ones earn their place and which ones you are paying for out of habit. The honest answer is not to cancel everything and start again.
The alternative worth knowing about is owning a system built around your own jobs: your membrane types, your typical cure variance by season, your certificate and warranty paperwork, your flood test timing, rather than a generic tool built for every trade on the market at once. That is a choice you can make once you can see, from your own numbers, where the generic tool is costing you margin and where it is doing its job fine.
How does Data First Coaching approach this?
Data First Coaching, built by Greg Allan, starts from the waterproofer's own job data inside the Trade Business Intelligence, not from a conversation about how busy the diary looks. It looks first at actual time spent against quoted time on jobs where cure time ran long, because that is where margin quietly disappears without ever being raised as a variation. Greg puts it plainly: “the job still gets done, you still charge the money, so you think you're doing okay.” Finding where that gap actually starts, rather than treating the symptom again on the next job, is the point.
The how, the systems and the agent builds that catch this for a waterproofing business are worked through inside the Academy, with other members, because the Trade Business Intelligence is powered by every member for every member. It is built for owners who are open minded, innovative and willing to share what they learn with the rest.

