By Greg Allan, tradesman and creator of Data First Coaching
How many hours a week on the tools is too many for a demolition contractor?
For most demolition contractors, somewhere around twenty hours a week running the excavator, driving the truck or supervising a hazardous removal is the point where growth stops dead. Past that, the week is full and there is nothing left over for the office side of the business.
This is not about working hard enough. A demolition contractor can run a clean site, keep dust and noise within what the council and the neighbours expect, and still be stuck, because every hour on the machine or inside a soft strip is an hour not spent on the phone lining up the next job. The work on site is real and billable. The work that brings in the next strip-out is not happening at all.
The danger zone is not a target to avoid out of principle. It is the point where the owner's own hours become the ceiling on how much work the business can take on, no matter how good the crew or the machinery is.
Why does the climb and slide pattern keep demolition contractors stuck?
Because demolition work is lumpy by nature. A house demo or a commercial strip-out finishes, there is a gap, and then the next one has to be found, quoted and permitted before the crew sits idle. If the owner is on the tools for that whole stretch, nobody is filling the gap.
The pattern looks like this: the owner gets off the tools for a stretch, catches up on quotes, follows up outstanding permit applications, chases a salvage opportunity on a building that is about to come down. Work comes in. Then the new jobs need running, so the owner goes back onto the excavator or the truck to get them done, and the sales and quoting work stops again.
It climbs, then it slides. For a demolition contractor this cycle is often sharper than in trades with steadier, ongoing work, because one site finishing before the next is secured is the normal shape of the job, not the exception.
What number in your own business actually shows where this starts?
It is not a feeling about being flat out. It is the split, week by week, between hours spent on site running machinery, supervising asbestos removal or on the soft strip crew, against hours spent quoting, chasing permits, and following up tip dockets and salvage leads.
Most demolition contractors can tell you they are busy. Few can tell you, without checking, what proportion of last month went to billable site work versus the non-billable office side that keeps the pipeline full. That split, tracked over a few months rather than guessed from memory, is what shows whether the business is actually growing or just cycling between busy and quiet.
This is the data first part of it: a decision about hiring or about how the owner spends the week, made on a feeling, is usually made on an old picture of the business. The owner's own numbers, not a memory of a hard month, show where the real ceiling is.
What changes when AI agents take over the quoting and permit chasing?
An AI agent is software that does a piece of office work the way the owner would do it themselves, with their own prices, their own wording and their own rules, rather than a generic version built for any demolition contractor. It does not replace the owner's judgement, it takes the repeatable parts off the owner's plate.
For a demolition contractor that can mean the preliminary quote for a soft strip or structural job getting drafted from the site details, a permit application getting chased with council instead of sitting untouched, or a salvage lead getting followed up before the building comes down and the opportunity is gone. None of this needs the owner standing in front of the excavator to happen.
AI agents working alongside the crew mean the owner's hours that used to go onto the tools can go onto the decisions only the owner can make, while the agents handle the chasing and the paperwork that used to get neglected because there was no time left.
Which hire actually gets you off the excavator and onto the phone?
It is not another admin person and it is not a second salesperson. It is the first operator or labourer hired specifically to take over the machine and crew hours the owner has been doing personally, so those hours become sales and marketing capacity instead of billable site time.
Until that hire is made, every hour the owner spends running the excavator or driving the truck is an hour the business cannot spend finding its next job. Once it is made, the owner's week has hours in it for quoting the next strip-out, following up a permit that has stalled, and chasing the salvage and recycling deals that often get missed when nobody has time to make the call.
This is the hire that breaks the ceiling on growth for a demolition contractor who is still on the tools. The ops manager hire, for scheduling and running multiple crews, comes later, once there is enough work on to need it.
How does Data First Coaching approach this?
Data First Coaching, built by Greg Allan, starts from the demolition contractor's own numbers through the Trade Business Intelligence, not from a description of how busy the week feels. It looks first at the actual split between hours on site and hours spent quoting, chasing permits and following up salvage, because that split usually shows where the climb and slide pattern really starts, rather than treating the symptom of a quiet month after month.
From there, the how, which hire to make first, how to shape the work an AI agent takes on, and how to hold the gain once it is made, is worked through inside the Academy, with other members. The Academy is built for owners who are open minded, innovative and willing to share what they learn, because the Trade Business Intelligence is powered by every member for every member.

