Articles

How can cabinetmakers cut time spent on shop drawings and site measures?

For a cabinetmaker, the real fix is pricing the shop drawing and the site measure as part of the finished kitchen, wardrobe or vanity, with their own time allowance, rather than treating them as free prep before the job starts. When that time is bundled into the quote and tracked against what actually happens, running over shows up straight away in the job's gross profit margin instead of quietly eating the owner's own hours between the quote and the install.

Places in the Academy are limited. 9,000+ owners trained, 4.9 stars from 123 Google reviews.

  • Data first coaching
  • Your nights back
  • Every job priced to make money
  • 9,000+ owners trained
  • Greg is the only coach
  • 20 years in trade, 10 coaching
  • Beat 9pm
  • Places are limited
Greg on videoAllow 60 minutes labour when you can do it in 30

By Greg Allan, tradesman and creator of Data First Coaching

Why do shop drawings and site measures always seem to eat more time than quoted?

Most cabinetmakers treat the site measure and the shop drawing as something that happens before the real job starts, a quick visit and a quick drawing on the way to the CNC and the workshop. The time spent on either rarely gets tracked against anything, so when a site measure runs long because a wall is out of square, or a shop drawing needs three revisions before the builder signs off, that time just disappears into the week. It was never priced, so it was never protected, and nobody notices until the job's margin looks thinner than it should.

What happens when a site measure runs long or a shop drawing needs redoing?

A kitchen quoted at a certain price can still come back with a shop drawing that takes far longer than expected, because the client changed the benchtop or swapped laminate for two pack after the first version went out. Each revision, each extra trip to re-measure a wardrobe or a vanity, adds hours that were never in the price. By the time board, edging, hardware and install are stacked on top, the gap between what the job was quoted at and what it actually returns is often set long before anyone in the workshop picks up a tool.

How do you price a site measure and shop drawing as part of the job, not before it?

If your clients see the site measure and the shop drawing as separate, free steps, you are training them to expect free prep on every kitchen, wardrobe or vanity that follows. Your client is paying for the finished joinery, not for the separate steps that got it there, so a site measure or shop drawing works better as a priced item with its own time allowance, built into the quote the same way a CNC run or an install day is.

That means giving the site measure and the shop drawing a known amount of time before you ever walk in the door or open the drawing software. A deposit that covers the design stage, with the measure and drawing already allowed for inside it, changes how the job reads to the builder or the homeowner too: it looks like one finished price, not a string of visible steps they can question or try to get for nothing.

What number tells you whether your site measures and shop drawings are actually making money?

The number that tells the truth is the time allowed for a site measure or shop drawing against the time actually spent on it, not a feeling that a particular job dragged on. This is the data first part of running a joinery business: when the allowed hours and the actual hours are tracked job by job, a pattern shows up that memory alone never catches, whether it is one client who always changes the design twice or one type of kitchen layout that consistently runs long.

It also matters who is doing the measure or the drawing. A team member will rarely match the owner's own fastest time on a site measure or a shop drawing, so the allowance needs a buffer built in above what the owner could do solo. Training closes that gap over time, cutting the allowance before that happens just moves the same lost hours onto someone else's timesheet.

How can AI agents take the admin out of shop drawings and site measures?

An AI agent is software that does a job the way you would, using your prices, your wording and your own rules, so it can sit inside the parts of pre-production that do not need a person's judgement. For a cabinetmaker that might mean chasing a builder for confirmed dimensions before a site measure is booked, keeping shop drawing revisions and sign offs in order, or flagging a job the moment its actual hours pass what was allowed, so the owner sees it before the install date, not after.

Picture a cabinetmaker who had no clear picture of where his own time went between quoting a kitchen and getting it on site, or which parts of a shop drawing and a site measure genuinely needed him and which did not. He mapped out the full run of a job, from first enquiry to final install, and marked each step as work for a person or work an AI agent could carry, then tracked how long each step actually took inside the business's own system. Nothing about the drawing or the measure itself changed. What changed was that the time was finally visible, and priced.

AI agents will not make a wall square or stop a client changing their mind about a benchtop. What they can do is make sure the hours a site measure or shop drawing actually takes are captured and checked against what the job was quoted for, so the gap between quote and reality shows up in the numbers instead of in the owner's evenings.

How does Data First Coaching approach this?

Data First Coaching looks at a cabinetmaker's own numbers before anything else, starting with the time allowed against the time actually spent on jobs like a site measure or a shop drawing. Greg Allan teaches checking “the allowed billable hours divided by actual hours on site”, because that single number shows whether pre-production work is priced the way the rest of the job is, or quietly carrying hours nobody is paying for. The Trade Business Intelligence reads this alongside ten years of coaching trade businesses to find where a cabinetmaker's time is really going, and where it starts. The how, including the systems built from that data, is worked through inside the Academy, with members who are open minded, innovative and willing to share, because the Trade Business Intelligence is powered by every member.

Also asked

More questions owners ask.

Should a cabinetmaker charge separately for a site measure, or build it into the quote?

Either can work, but the point is that the time must be allowed for somewhere and tracked. Folding it into one finished price for the kitchen, wardrobe or vanity often reads better to the client than a separate line item they can query or try to avoid.

What if a client wants changes after the shop drawing is already signed off?

Treat it as new work with its own time allowance, not an extension of the original drawing's price. A design change after sign off, whether it is a different benchtop or a swap from laminate to two pack, is a fresh decision for the client to make, with a cost attached.

Does tracking time on site measures slow down how fast a cabinetmaker can quote?

No. Once a site measure and a shop drawing have a known time allowance, quoting them becomes faster, not slower, because the owner is pricing against a known figure rather than guessing fresh on every kitchen or wardrobe.

Is this only useful for custom kitchens, or does it apply to flat pack jobs too?

It applies to both. A flat pack run still needs a site measure and a shop drawing, and the same question applies: is the time spent on them covered by the price, or is it quietly unpriced work sitting ahead of the CNC and the install.

Data First Coaching

Coaching That Starts From Your Data.

Data First Coaching is the trade business coaching method created by Greg Allan, founder of Tradies Success Academy. Before any advice is given, the Trade Business Intelligence Agent reads the owner's own job management and finance data, so the coaching starts from what the numbers show this week, not from what the owner can remember or explain. It finds the root cause of a problem, then puts in the system that fixes it.

How most coaching works

Most coaching starts with the owner explaining the business.

  • The first hours go on the owner describing the business to a coach.
  • The picture is out of date within weeks, because the numbers move every week.
  • So the advice treats what the owner happened to notice, which is usually a symptom.
  • Too often it comes from someone who has never run a trade business, or has only just started one.
  • The owner pays for the explaining, then pays again when the advice does not fit.

Data First Coaching

Data first starts from your numbers, not your memory.

  • The Trade Business Intelligence Agent reads your job management and finance systems first.
  • It sees your quotes, jobs, time on site and money as they are this week, not as you remember them.
  • It finds where the problem actually starts, not where it shows up.
  • You put in the system that fixes it at the root, and the data shows whether it worked.
Typical coaching against Data First Coaching
Typical coachingData First Coaching
Where it startsYou explain the businessYour own job and finance data
How current it isAs at the last meetingUpdated as your numbers change each week
What it fixesThe symptom you noticedThe root cause the data shows
Who coaches youOften someone who has never run a trade businessGreg Allan, who built a trade business a general manager now runs
The answer to growthUsually another wageAgents on the office work, people on customers and the crew
Your softwareAnother subscription or agencyTools you build on your own data, around how you work

Fix the root cause, once

The data names the real problem, so the system you put in fixes it once instead of patching the same symptom every month.

Own your software

Build your own tools on your own data, shaped around how your jobs run and how your customers buy. Cancel the subscriptions and agencies that were never built for your business.

A more human business

Agents do the non-billable work: the quoting, invoicing, chasing and reporting. Your people spend the day on customers and the crew, so relationships get better and the team performs.

Why Greg

You speak to the owner who has already done it.

Greg built Response Electricians in Perth into a 30+ staff business with 1,950+ five-star reviews. A general manager runs it.

He has trained 9,000+ trade business owners across Australia and New Zealand.

He grew a coaching company to 35 staff, a CEO and 15 coaches, then cut it back so every owner deals with him directly.

Most coaching companies hand you to a salesperson, then to a coach who has never run a trade business. Here you get the owner.

The Academy is in demand because it works, and Greg keeps places limited on purpose so every business gets looked at properly, by him. He reads every application himself, interviews the owners who fit and only takes on owners who are building for the right reasons and give back to the group. Apply now and he'll be in touch when a place opens.

Illustration: a trade business owner standing over three office staff buried in paperwork at night.
The old way

More customers meant more people doing the computer work, and more wages nobody invoices.

Illustration: a tradesman shaking hands with a homeowner in her driveway, his phone showing jobs quoted and invoiced.
The new way

You stay with your customers and your team. The office stops landing on you.

The old way

More jobs. More paperwork. Less of the owner left.

Most trade businesses grow the same way.

More jobs means more quoting, invoicing, chasing and scheduling.

None of it gets paid for.

So the owner does it at night, after a full day on site.

Or hires an office person to do it.

The office grows. The wages grow. The margin does not.

And the owner is still the one everything waits on.

Where we take you

More work. More profit. More of you left.

The phone rings with the jobs you want, at the price you set.

You grow when you're ready, never faster than the business can carry.

Every job is priced to make money, so the busy months show up in the bank.

The best tradies in your area want to work for you, and they stay.

The chasing, the paperwork and the 9pm admin stop landing on you.

The business runs the day. You pick which parts of it you're in.

Bigger, without the headaches. Getting bigger stops meaning getting busier.

P.S.

P.S. Applying costs nothing and there is no obligation. While you wait, the Tradies App is free for trade business owners, so you can start on the lessons tonight.