By Greg Allan, tradesman and creator of Data First Coaching
Why isn't there one piece of software built for cabinetmakers?
There is no single program built to run a cabinetmaking business from the first site measure to the last install day, because the trade has two different worlds inside it. The workshop runs on CNC, board, edging and hardware. The site runs on measures, shop drawings, builder handovers and install labour. Most software is built for one of those worlds, not both.
A cabinetmaker shopping for software often starts by looking for the one app that does everything. That app rarely exists. Job management tools built for trades in general handle quoting and scheduling well but know nothing about a cut list or an edging run. Nesting software on the CNC handles the workshop beautifully but has no idea what the builder agreed to at handover, or how long a deposit sat unpaid before a job even started.
The result is a business running on a mix of paper plans, spreadsheets, and whatever came bundled with the CNC machine, each holding a slice of the job and none of them talking to each other.
Where does a cabinetmaking business actually lose track of its margin?
The margin on a kitchen or wardrobe is most often lost between the shop drawings and the install, where labour on CNC, edging, board prep and the install day never gets properly recorded against that specific job. Without that record, a cabinetmaker can look busy every week and still not know which jobs made money.
A business quoting with a ruler, pencil and a plan on paper, then tracking labour the same way, can lose control of that picture once it grows past one person doing everything in the workshop and on site. Two kitchens quoted at the same rate can finish with very different results once real labour, a remake, and a slipped lead time are counted in. If that labour was never documented against the job, the owner never sees it.
That is not usually a pricing problem. It is a data problem. The answer is already sitting in job folders, timesheets and supplier invoices, it has just never been pulled together by job.
What should you look for instead of one all in one system?
You look for the combination that covers how your jobs actually run, not one program that claims to do it all. For a cabinetmaker, that typically means something that handles site measures, shop drawings and quoting on one side, and tracks CNC time, board and hardware use, and install labour against each job on the other, joined up so a job's true cost shows up in one place.
Start from where your own time actually bleeds onto paper first. If site measures and design changes still travel as marked up plans and sticky notes between you and the workshop, that is the gap worth closing first. If the CNC runs well but install labour never makes it back to the job file, that is a different gap, with a different fix.
This is where building from your own data first matters more than copying a list of apps other cabinetmakers use. The part of the process costing a cabinetmaker real money is rarely the same from one workshop to the next.
How do AI agents fit into a cabinetmaker's workshop and site work?
An AI agent is software that does a piece of the office work the way you would do it yourself, with your pricing, your wording and your rules. For a cabinetmaker, that can mean an agent turning a site measure into a shop drawing request, chasing a deposit, or logging install labour against a job without you touching a keyboard at night.
Picture a cabinetmaker quoting a kitchen the old way: ruler, pencil, a plan on paper, then typing it all up back at the workshop before it can go to the builder. With the right system and an AI agent sitting behind it, that same quote can take minutes once the measurements and standard pricing are already structured, because the agent is doing the assembling rather than the cabinetmaker. The time that frees up goes back onto the tools, not into chasing paperwork.
A second agent can sit on the labour side, picking up CNC and install hours as they are logged and matching them back to the job, so the true cost of that kitchen or wardrobe is visible while the job is still running, not months later once the invoice has already been paid and the margin is long gone.
Should you keep the off-the-shelf software you already use?
Often, yes, in part. Some off-the-shelf tools suit a cabinetmaker well, particularly things like nesting software on the CNC or basic scheduling, and the sensible move is to keep what already earns its place rather than throw everything out and start again.
The job is to look at your own data and see which tools are feeding good information back into the business, and which ones are just another place to type the same job details in twice. A tool that saves time on the workshop floor but creates extra admin back at the office is not saving the business anything, it is just moving the cost somewhere less visible. That is a decision a cabinetmaker's own numbers can answer honestly, where a sales claim from a software company cannot.
How does Data First Coaching approach this?
Data First Coaching starts from the cabinetmaking business's own numbers before it looks at any software, because the gap between workshop and site rarely shows up the same way twice. Through the Trade Business Intelligence, Greg Allan looks at where labour and job documentation are still sitting on paper, and where that is quietly costing margin on real kitchens, wardrobes and vanities. Greg is upfront that “the perfect single program doesn't really exist”, so the work is finding which part of the cabinetmaker's own workflow needs fixing first. The how of building that, system by system, is worked through inside the Academy, with members, because the Trade Business Intelligence is powered by every member who is open minded, innovative and willing to share what they learn.

